Smartcharger 250W – Cyclic Applications

The SR SmartCharger is designed to recharge your battery in the shortest practicable time with programmable parameters to suit your specific application.Smartcharger 250W

Smart Chargers or Boost Chargers
Helios Power Solutions Smart Battery Chargers or also known as Boost Chargers, are able to respond to the condition of a battery, modifying their charging actions accordingly. Our Smart Chargers are microprocessor controlled and allow for the maximum charge into your batteries to minimize the charge time. Boost mode allows for a high current, high voltage charging cycle, also allowing for the maximum charge into the battery in the shortest possible time. Float mode allows for the battery to be held at optimal voltage with a small trickle charge still being generated, to ensure that the battery is ready to when used.
Other features of our Smart Chargers include:
  • Designed to charge both sealed and flooded lead-acid battery types
  • Come with temperature compensation to ensure that the correct voltage is applied to the battery, irrelevant of the ambient temperature
  • Provide fully automatic battery recovery in the shortest possible time
  • Includes with both ‘boost’ and ‘float’ mode
A simple charger works by supplying a constant DC source to a battery being charged. The simple charger does not alter its output based on time or battery charge. This simplicity means that simple chargers are very cheap, although there is a trade-off in quality. A trickle charger is typically a low current battery charger, used to charge small capacity batteries




Model Output Voltage¹ (float) Output Voltage¹ (max boost) Output Current (continuous) Min – Max Battery Size2
SR250E12 13.8 14.7 16.7A 65-200 Ah
SR250E24 27.6 29.4 8.3A 30-100 Ah
SR250E36 41.4 44.1 5.6A 22-70 Ah
SR250E48 55.2 58.8 4.2A 15-50 Ah
¹ May be adjusted to suit battery specifications
²  Guidelines only.   Please check manufacturer’s recommendations.


Input STANDARD: 180V – 264VAC
Frecuency 45-65Hz
Fusing Internal AC input fuse
Isolation 1KV DC input – output / earth
Efficiency > 85%
Inrush current Soft start circuit
Output power 250W
Output voltages Refer to the model table
Voltage adj. range Approx 95 – 105% of V nominal
Temp. Compensation Temperature sensor on 1.7m lead with
adhesive pad:  -4mV / °C / cell ±10%
Current Limit Constant current limit on overload & short circuit
Output Protection Automatic shutdown if battery leads reversed
or short circuit on output
Line regulation < 0.2% over AC input range
Load regulation < 0.4% open circuit to 100% load
Noise <1%
Drift 0.03% / °C
Hold-up time 15 – 20 ms (nom. – max. Vin) without  battery
OVP Over-voltage protection on output at ~ 130% of nominal output voltage
Thermal Protection Yes
Alarm & boost/float indication relays* Mains fail
Batt low (set at 1.83V/cell = 11, 22V, etc)
Alarm Relay Contacts C – NO – NC  full changeover   Rated 1A @ 50V DC or 32VAC
Adjustable Parameters All firmware parameters listed under features may be adjusted at time of ordering
Switch/ LED Indication & functions BOOST:  Red
FLOAT:  Green
STANDBY: Red (Push button to turn output off/on).
Refer to instruction manual  for full list of LED Operation codes
Factory Programmable parameters (default settings shown in brackets; please note that some parameters are interdependent of each other) Start up in boost or float mode (Boost)
Current terminated boost  (Yes)
Current initiated boost  (Yes)
Start boost on mains return (Yes)
Pre-boost state timer 1-255 minutes (1)
Max boost charge time 0-48 hours (24)
Pre-float state timer 1-255 minutes (1)
Resume prior state upon mains return timer 1-255 minutes (10)
Resume on boost charge upon mains return 0-255 hours (24)
Pre-forced float timer 1-255 minutes (1)
Delay before mains fail recognition 4sec – 8.5minutes(5 minutes)

Related Products

New Rack Mount DC Power Supply For Base Station Repeaters 2020